home
***
CD-ROM
|
disk
|
FTP
|
other
***
search
/
QRZ! Ham Radio 4
/
QRZ Ham Radio Callsign Database - Volume 4.iso
/
digests
/
homebrew
/
940184.txt
< prev
next >
Wrap
Internet Message Format
|
1994-11-13
|
11KB
Date: Wed, 6 Jul 94 04:30:34 PDT
From: Ham-Homebrew Mailing List and Newsgroup <ham-homebrew@ucsd.edu>
Errors-To: Ham-Homebrew-Errors@UCSD.Edu
Reply-To: Ham-Homebrew@UCSD.Edu
Precedence: Bulk
Subject: Ham-Homebrew Digest V94 #184
To: Ham-Homebrew
Ham-Homebrew Digest Wed, 6 Jul 94 Volume 94 : Issue 184
Today's Topics:
1/4-wave coax filters ?
Camcorder viewer needed.
ex
General electronics newsgroup?
microwave mixer details (2 msgs)
RF Feedback in Mic while talking and touching mic.
Want Terman book
Send Replies or notes for publication to: <Ham-Homebrew@UCSD.Edu>
Send subscription requests to: <Ham-Homebrew-REQUEST@UCSD.Edu>
Problems you can't solve otherwise to brian@ucsd.edu.
Archives of past issues of the Ham-Homebrew Digest are available
(by FTP only) from UCSD.Edu in directory "mailarchives/ham-homebrew".
We trust that readers are intelligent enough to realize that all text
herein consists of personal comments and does not represent the official
policies or positions of any party. Your mileage may vary. So there.
----------------------------------------------------------------------
Date: 6 Jul 1994 10:42:50 GMT
From: ihnp4.ucsd.edu!agate!howland.reston.ans.net!math.ohio-state.edu!jussieu.fr!univ-lyon1.fr!elendir@network.ucsd.edu
Subject: 1/4-wave coax filters ?
To: ham-homebrew@ucsd.edu
Hi !
Some time ago, I posted here some request regarding the design of empty
cavities to implement high-Q band-pass filters [for a repeater project].
I found some infos, but the dimensions of the required box seem to be
at best unpractical [Even for an UHF repeater].
Some OM told me about 1/4-wave "cavities" which seem to be in fact special
coaxial lines. Much smaller than true cavities, but with a wire running
through the empty space.
Does anybody have any info regarding this type of filtering device ? I
understand it also work by a resonnating process, maybe with a clever
impedance transformation, but I have no further clue. Also, the OM I talked
with admitted he had bought it from a commercial source, then had them
fitted for the application.
I understand also that the Q of those filters is much lower than those of
true cavities.
Thanks,
Vincent.
--
F1RCS - Worldwide Friendship through Amateur Radio
ENST, Ecole Nationale Superieure des Telecommunications, Paris
------------------------------
Date: 5 Jul 1994 23:19:49 -0700
From: nntp.crl.com!crl.crl.com!not-for-mail@decwrl.dec.com
Subject: Camcorder viewer needed.
To: ham-homebrew@ucsd.edu
Hello all-
I am interested in making some "VR" glasses except instead of using small
computer screens or whatever they are, I would like to use the small
screen that is looked into when you use a camcorder. Does anybody have
any idea where I could obtain these? I would appreciate addresses,
phone#'s, and, prices. Thanx in advance.
------------------------------
Date: 5 Jul 94 20:19:12 EST
From: ccsua.ctstateu.edu!white@yale.arpa
Subject: ex
To: ham-homebrew@ucsd.edu
Toroids ......
What is the significance of the PHASING dots on a schematic?
And
What if the toroid requires 55 turns and you can only fit 35 turns on the
core???
Any help appreciated. I'm working on the 7MHz Optimized.
Regards
Harry
------------------------------
Date: 5 Jul 94 16:26:44
From: ihnp4.ucsd.edu!usc!howland.reston.ans.net!math.ohio-state.edu!magnus.acs.ohio-state.edu!csn!news.usafa.af.mil!usafa2!jcmiller@network.ucsd.edu
Subject: General electronics newsgroup?
To: ham-homebrew@ucsd.edu
In article <2uvbe5$grc@usenet.INS.CWRU.Edu> sct@po.cwru.edu (Stephen C. Trier) writes:
Mathias Hjelt <mahjelt@freenet.hut.fi> wrote:
> Are there any newsgroups for general electronic stuff?
Take a look at sci.electronics. The volume is high, but the noise level
is surprisingly low.
Stephen
--
Readers of this group may also be interested in sci.electronics.repair, which I
just newgrouped here (and which will presumably be carried most places).
73,
Jeff
--
Jeff Miller, NH6ZW/N0, AFA5MJ/AFF5CO (ex WD6CQV, AFA1DO, AFA8JM, AFA1HE)
USAFAnet Manager and General Troubleshooter [jcmiller@gems.usafa.af.mil] or
HQ USAF/DFYC, USAF Academy, CO 80840 [millerjc%dfyc@dfmail.usafa.af.mil]
55: It's not a good idea, it's just the law. E-mail for NMA info.
------------------------------
Date: Tue, 5 Jul 1994 12:56:07 GMT
From: spsgate!mogate!newsgate!news@uunet.uu.net
Subject: microwave mixer details
To: ham-homebrew@ucsd.edu
I dug up an old 73 Magazine article from 1980 for an MDS microwave
downconverter. It uses an oscillator with half the frequency of the
desired local oscillator and a half-wave air-line microstrip mixer. It
converts 2154 and 2160 down to channel 3 (or 2 or 4 depending on how it
is tuned).
The microstrips are held above the ground plane 1/16 in, and the strips
are
3/16 in wide. The grounded end is 2-3/4 (7cm) in long and the rf side is
2-5/8 in (6.77cm). The diodes are oriented as shown (HP 5082-2835), and
there is half an inch between the 2 strips for the diodes. The IF out is
tapped at the half way point of the ungrounded strip. I have not shown
the
high and low pass filters, and have noted the original frequencies.
2154-2160MHz
RF In
|
|
|
_____________________________ v___________________________
Gnd | |-|<-| |
End | | | |
|_____________________________|->|-|___________________________|
^ ^
| |
| |
LO In IF Out
1108MHz 61MHz
What I want to do with this is convert the whole thing to a block
converter
for 2500 to 2700 MHz down to 200-400 MHz. The local oscillator would be
1150
MHz, easily in range of the local oscillator of this article. I want to
build
this on a double sided FR4 board as well.
I have pretty well figured out the width of the strips to keep the
impedance
the same as in the air case. But I don't know if the lenght of the half
wave
strips should be tuned for the local oscillator or the incoming signal,
and
whether or not the 1/2 inch between the strips is all that critical.
Does anyone know?
Thanks,
Dave DiCarlo
r14793@waccvm.sps.mot.com
------------------------------
Date: Tue, 5 Jul 1994 15:45:47 GMT
From: mozo.cc.purdue.edu!sage.cc.purdue.edu!aj@purdue.edu
Subject: microwave mixer details
To: ham-homebrew@ucsd.edu
David DiCarlo <r14793@waccvm.sps.mot.com> writes:
> 2154-2160MHz
> RF In
> |
> |
> |
> _____________________________ v___________________________
> Gnd | |-|<-| |
> End | | | |
> |_____________________________|->|-|___________________________|
> ^ ^
> | |
> | |
> LO In IF Out
> 1108MHz 61MHz
> But I don't know if the length of the half wave strips should be
> tuned for the local oscillator or the incoming signal, and whether or
> not the 1/2 inch between the strips is all that critical.
One of the two should be tuned for the incoming signal's frequency, I
would guess, as this would have the effect of making the incoming signal
stronger through resonance. The other should be tuned to the incoming
signal plus or minus (looks like plus from the length of the IF Out
side, and jibes with good converter design principles) the IF frequency.
The half inch is probably just enough room to mount the mixer diodes, as
microwave types tend to be really big-cased for some reason. When you get
the diodes, measure them and set the spacing between the strips to be
as close to the ends of the diodes as possible. Your biggest worry
about losses is from inductance and conductance of solder at these
frequencies. Pb/Sn solder is measurably less conductive at these
frequencies than clean copper, but not so much that you'll really
notice. Bad joints are more the issue.
I've worked at 915MHz for two years, and this isn't a lot different in
the basics. Good luck on your project!
: John Dormer
: aj@sage.cc.purdue.edu
: jad@mdn.com
------------------------------
Date: 6 Jul 1994 07:11:54 GMT
From: ihnp4.ucsd.edu!library.ucla.edu!agate!howland.reston.ans.net!cs.utexas.edu!news.tamu.edu!cschmidt@network.ucsd.edu
Subject: RF Feedback in Mic while talking and touching mic.
To: ham-homebrew@ucsd.edu
I have a problem with RF feedback in my mic only when I touch
the mic to my face while speaking. It seems that it is making the
Radio Squeal. I have a RCI 2950 with a Texas Star DX 667V amplifier'
and a cheap Mag-mount base with a base loaded antenna with about
a 3.5" whip on top. I do not have this problem when not using
the amplifier. On AM it sqeuals when I talk. On SSB it is fine until
I start talking and then it Stays keyed up and squeals for a few seconds then
stops. I have had this problem with other Equipment too. But not this
bad.
If anyone knows of some RF filtering Technics for Microphones
I would appreciate it very much. I can't DX without the amp very
well because of the Low gain of the antenna. I am new at this so
if you get real technical with terms please remember to elaborate a
little. If anyone else has had this same problem with the 2950 or
any other radio I would be glad to hear how you got rid of the squeal
and the feedback.
thanx in adv.
73,
chris
Houston tx.
------------------------------
Date: Tue, 5 Jul 1994 15:35:08 GMT
From: ihnp4.ucsd.edu!sdd.hp.com!hp-pcd!hpcvsnz!tomb@network.ucsd.edu
Subject: Want Terman book
To: ham-homebrew@ucsd.edu
Mike Czuhajewski (Mike.Czuhajewski%hambbs@wb3ffv.ampr.org) wrote:
: I'm looking for a reasonably priced copy of Radio Engineers Handbook
: by Terman, dated somewhere back in the WWII era. (Please note the
: exact title; there are 3 other books by the same author with the word
About 4 months ago I picked up a copy in a used book store for under
$10. I'm posting this only to give an idea of prices; I'm not at
all interested in parting with it at any price near that.
73, K7ITM
------------------------------
End of Ham-Homebrew Digest V94 #184
******************************